The compression ratio tells a compressor how strongly to reduce the signal once it goes over the threshold. At 4:1, every 4 dB the input rises above the threshold comes out as only 1 dB above it. At 2:1, 2 dB in becomes 1 dB out. At ∞:1, nothing gets past the threshold at all.

The ratio is the most visible number on a compressor and the one beginners obsess over. It matters, but it never works alone: the threshold decides how much of the signal the ratio applies to, and attack, release and knee decide how much of the nominal ratio you actually hear.

What is compression ratio?

The ratio compares the change in input level above the threshold with the change in output level above the threshold, both in decibels. A ratio of R:1 means an overshoot of R dB at the input becomes 1 dB at the output. The higher the ratio, the flatter the output and the more gain reduction you get for the same overshoot.

The same idea is used across dynamics processing:

  • Compression: ratios above 1:1, roughly 1.2:1 to 10:1.
  • Limiting: very high ratios, conventionally 10:1 and up, with ∞:1 as the true brickwall. Where compression ends and limiting starts is a convention, not a law; attack time matters as much as the ratio. See limiter.
  • Downward expansion: ratios that increase dynamic range below the threshold, usually written 1:2, 1:4 and so on. See expander.
  • Gating: a very steep expansion ratio, so the signal drops sharply once it falls below the threshold. See noise gate.

Ratio as slope

On a graph of input level against output level, the ratio is the slope of the line above the threshold. At 1:1 the line runs at 45 degrees. At 2:1 it’s half as steep, at 4:1 a quarter as steep, and at ∞:1 it’s flat. Some manuals and engineering texts call this the slope rather than the ratio, and some quote it as a fraction (a 4:1 ratio is a slope of 0.25).

Notation

Compression ratios are written with the larger number first: 4:1. Expansion ratios are usually written the other way around, 1:2, meaning 1 dB of change at the input becomes 2 dB at the output. You’ll also see expansion written as 0.5:1, and a few vintage manuals write compression ratios inverted. The math is the same; check which convention a manual uses.

History

Early broadcast compressors from the late 1930s, such as the Western Electric 110A (1937) and RCA’s 96-A, didn’t offer a ratio control. Their gain reduction came from variable-mu tubes whose gain changed with a bias voltage, so the effective ratio rose smoothly as the signal got louder. The Fairchild 660 and 670 (1959), designed by Rein Narma, work the same way: there’s no ratio knob, and the curve gets steeper the harder you drive the unit (a DC bias adjustment sets how the knee and ratio behave).

Selectable ratios arrived with solid-state designs. The Universal Audio 1176 (first units 1967) offers four ratio buttons: 4, 8, 12 and 20:1. The Teletronix LA-2A’s optical design has a Compress/Limit switch rather than a ratio control, with Universal Audio describing the average compression ratio as roughly 3:1 and the Limit setting as a much higher ratio. The dbx 160 (1976) brought a VCA gain element and RMS detection, which made precise, repeatable ratios practical, and dbx’s OverEasy soft knee, introduced on the dbx 165 in the late 1970s, popularized a gradual transition into the ratio.

In 1973 Eventide’s Omnipressor, conceived by company founder Richard Factor, went further: its ratio control ran continuously from expansion through compression to infinity and beyond into negative ratios, which Eventide called “dynamic reversal”. Digital compressors now offer continuously variable ratios from below 1:1 to ∞:1 as standard.

How compression ratio works

The formula

For a hard-knee compressor with threshold T and ratio R, and an input level x above the threshold (all in dB):

  • Output = T + (x − T) / R
  • Gain reduction = (x − T) × (1 − 1/R)

So the share of the overshoot removed is 1 − 1/R: half at 2:1, three quarters at 4:1, 90% at 10:1, all of it at ∞:1. This is why going from 2:1 to 4:1 is a big change, while going from 10:1 to 20:1 adds comparatively little.

Worked example

Threshold −20 dBFS, input peak −8 dBFS, so the overshoot is 12 dB:

RatioOvershoot inOvershoot outOutput levelGain reductionTypical character
1:112 dB12 dB-8 dBFS0 dBNo compression
1.5:112 dB8 dB-12 dBFS4 dBVery gentle leveling, bus glue
2:112 dB6 dB-14 dBFS6 dBGentle leveling
3:112 dB4 dB-16 dBFS8 dBModerate, general purpose
4:112 dB3 dB-17 dBFS9 dBFirm control, a common default
8:112 dB1.5 dB-18.5 dBFS10.5 dBHeavy compression
10:112 dB1.2 dB-18.8 dBFS10.8 dBOften treated as limiting
20:112 dB0.6 dB-19.4 dBFS11.4 dBLimiting
∞:112 dB0 dB-20 dBFS12 dBBrickwall limiting

Notice how quickly the extra gain reduction runs out: 4:1 already removes 9 of the 12 dB, and everything above 10:1 is fighting over the last 1.2 dB.

Ratio and knee

The formula above assumes a hard knee, where the full ratio applies the instant the threshold is crossed. With a soft knee, the ratio grows gradually through a region around the threshold: just below it the compressor is already working at a ratio slightly above 1:1, and only well above it does it reach the ratio you set. Many plugins let you set the knee width in decibels.

Nominal ratio vs effective ratio

The number on the control is the static ratio: what you’d measure with a steady tone held long enough for the compressor to settle. Music isn’t steady. With a slow attack, a short drum hit can be over before the compressor reaches full gain reduction, so the hit passes at something much closer to 1:1. With a fast release, gain reduction collapses between notes. The ratio you actually hear on program material, the effective ratio, is often lower than the dial says, and it differs from hit to hit.

How different gain elements behave

  • VCA (dbx 160, SSL bus compressor, most plugins): precise, predictable ratios that follow the formula closely.
  • FET (1176): fixed ratio buttons, with a character that changes with drive. In all-buttons-in mode, Universal Audio says the ratio goes to somewhere between 12:1 and 20:1 and the bias points throughout the circuit change, with a big jump in distortion.
  • Optical (LA-2A): no ratio control as such; the curve depends on the optical cell, the program material and how hard you drive it. The Compress/Limit switch selects a gentler or steeper behavior.
  • Variable-mu (Fairchild, Manley Variable Mu and similar): the ratio rises with level, so light settings sound gentle and heavy drive sounds like limiting.
  • Diode bridge (Neve 2254, 33609): selectable ratios; the 33609’s compressor section offers 1.5:1 to 6:1 according to the AMS Neve manual.

Below 1:1: expansion

Expansion ratios work below the threshold. At 1:2, a signal that falls 10 dB below the threshold comes out 20 dB below it. That makes quiet sounds quieter: useful for reducing bleed, room noise or headphone spill without the abrupt switching of a gate. Upward expansion, which makes loud sounds louder above a threshold, also exists but is less common.

Negative ratios

A negative ratio means the output goes down when the input goes up past the threshold. Loud hits come out quieter than soft ones, which turns drum hits inside out and pulls room sound and decay forward. The Eventide Omnipressor made this famous in the 1970s, and several modern plugins offer ratios below zero for the same effect. It’s a sound-design tool, not a mixing default.

Compression ratio in practice

Common starting points

These are widely taught starting ranges, not rules. Your threshold, attack and release will change what any of them sounds like.

Source or jobCommon ratio rangeWhy
Mix bus “glue”1.5:1 to 4:1Gentle, continuous control; a few decibels of gain reduction at most
Lead vocal (leveling)2:1 to 4:1Evens out phrases without obvious squeezing
Lead vocal (aggressive rock or pop)4:1 to 8:1 or morePins the vocal to the front of a dense mix
Bass3:1 to 8:1Holds the low end steady
Kick and snare3:1 to 6:1Shapes attack and sustain with the time constants
Parallel (smashed) bus8:1 to ∞:1Heavy, consistent squash to blend under the dry signal
Peak limiting10:1 to ∞:1Stops peaks going over a ceiling

Two strategies: low ratio, low threshold vs high ratio, high threshold

With a low ratio and a low threshold, most of the performance sits above the threshold and gets nudged down gently all the time. The result is smooth and often hard to hear as compression. With a high ratio and a high threshold, only the loudest peaks cross the line, but those get clamped hard. The body of the sound is untouched, and the peaks are controlled. Many engineers combine the two in series: one compressor catching peaks at a high ratio, another leveling gently at a low ratio. See threshold.

Documented examples

  • In a 2007 Sound On Sound interview, Chris Lord-Alge describes his lead vocals going through a “blue” 1176 at 4:1 with a quick release, and bass through a black 1176 at 4:1 with about 7 dB of gain reduction.
  • Andy Wallace told Mix in 2005 that he keeps his SSL bus compressor “pretty much” at 4:1 on automatic release; the interviewer had seen it reading about 4 to 6 dB of gain reduction on 3 Doors Down’s album Seventeen Days.
  • The 1176’s all-buttons-in mode, used heavily on drum room mics, is a case where the ratio label stops meaning much: the circuit’s whole behavior changes, not just the slope.

Genre tendencies

Classical and acoustic jazz recordings use little compression, and when they do, ratios tend to be low with gentle time constants. Rock, metal, hip-hop and modern pop lean on firmer ratios and more of them, often in series and in parallel. Broadcast speech processing typically uses high ratios to keep voices at a consistent level against noise.

Gear and software

  • Universal Audio 1176: buttons for 4, 8, 12 and 20:1, plus the all-buttons-in trick.
  • SSL 4000 G bus compressor: ratios of 2, 4 and 10:1.
  • AMS Neve 33609: compressor ratios from 1.5:1 to 6:1, plus a separate limiter section.
  • Empirical Labs Distressor: ratios of 1:1, 2, 3, 4, 6, 10 (an opto-style mode), 20 and “Nuke”, which Empirical Labs describes as pretty much brickwall limiting.
  • Teletronix LA-2A: Compress or Limit, no ratio knob.
  • Fairchild 660/670 and other variable-mu units: no ratio knob; the ratio rises with drive (on the Fairchild, a DC bias trim adjusts the knee and ratio).
  • Plugins: most offer a continuous ratio from 1:1 to ∞:1; some go below 1:1 for expansion or into negative ratios.

Common mistakes and myths

“A higher ratio makes it louder”

A higher ratio means more gain reduction, so the output gets quieter. Any loudness gain comes afterwards, from makeup gain. If a track gets louder when you raise the ratio, the plugin probably has auto makeup gain switched on.

“High ratio equals punch”

Punch usually comes from the attack setting letting the front of a hit through before gain reduction takes hold. A high ratio with a very fast attack does the opposite: it flattens the hit.

One ratio for everything

A default of 4:1 on every channel ignores how different sources behave. A dynamic acoustic guitar, a sustained synth pad and a slap bass don’t need the same treatment.

Judging the ratio without the threshold

A 10:1 ratio with the threshold set above every peak does nothing. A 2:1 ratio with the threshold 20 dB into the signal does a lot. Always think of ratio and threshold together.

“1:1 is bypass”

On a clean digital compressor, yes. On analog hardware or an analog-modeled plugin, the signal still passes through the circuit and its transformers, tubes or saturation, so a 1:1 setting can still color the sound.

CompressorLimiterDownward expanderNoise gate
Typical ratio1.2:1 to 10:110:1 to ∞:11:1.5 to 1:4Very steep expansion (often 1:10 or more) or simple on/off
Acts onSignal above thresholdSignal above thresholdSignal below thresholdSignal below threshold
Effect on dynamic rangeReduces itReduces peaks onlyIncreases itRemoves low-level signal
Typical useLeveling, shapingPeak control, loudnessReducing bleed and noise gentlyRemoving bleed and noise

Related controls: the threshold decides where the ratio starts to apply; the knee decides how smoothly it’s reached; makeup gain restores the level the ratio took away.

Standards and references

No standard prescribes compression ratios for music. Manufacturers specify ratios as static values measured with steady signals. For the math, the Journal of the Audio Engineering Society tutorial “Digital Dynamic Range Compressor Design: A Tutorial and Analysis” (Giannoulis, Massberg and Reiss, 2012) sets out the gain computer equations for hard and soft knees used across digital compressors.

  • Compressor: the device the ratio belongs to.
  • Threshold: where the ratio starts to apply.
  • Compressor knee: the shape of the transition into the ratio.
  • Gain reduction: what the ratio produces.
  • Limiter: the high-ratio end of the scale.
  • Expander and noise gate: ratios below 1:1.
  • Parallel compression: where very high ratios are blended in rather than used straight.
  • Dynamic range: what compression ratios reduce.

FAQ

What does a 4:1 compression ratio mean?

For every 4 dB the input rises above the threshold, the output rises only 1 dB. A peak 8 dB over the threshold comes out 2 dB over, so the compressor applies 6 dB of gain reduction.

What does 2:1 mean on a compressor?

Every 2 dB above the threshold becomes 1 dB above it. Half of each overshoot is removed, which is gentle compression.

Is 10:1 compression or limiting?

Ratios of 10:1 and above are conventionally called limiting, but the line is fuzzy. A limiter also needs a fast attack to stop peaks reliably.

What does ∞:1 mean?

An infinite ratio: once the signal reaches the threshold, the output doesn’t rise any further. This is brickwall limiting.

What ratio should I use on vocals?

Around 2:1 to 4:1 is a common starting point for natural leveling. Aggressive rock and pop vocals often get higher ratios or two compressors in series.

What ratio should I use on the mix bus?

Low ratios, commonly 1.5:1 to 4:1, with only a few decibels of gain reduction. The SSL bus compressor at 4:1 with auto release is a classic setting.

Why does my track get louder when I raise the ratio?

Probably because auto makeup gain is on. A higher ratio on its own makes the output quieter.

What is the difference between ratio and threshold?

The threshold sets where compression starts; the ratio sets how strongly the signal is reduced once it’s past that point.

What ratio does a noise gate use?

A gate acts like a downward expander with a very steep ratio, or simply switches between open and a fixed amount of attenuation (the range).

What is a negative compression ratio?

A setting where louder input above the threshold produces quieter output. The Eventide Omnipressor popularized it as “dynamic reversal”; it’s used as a special effect.

What ratio is the 1176 all-buttons-in mode?

Universal Audio says it lands somewhere between 12:1 and 20:1, but the bigger change is the altered bias and greatly increased distortion, which is why it sounds so aggressive.

Does the ratio on an LA-2A change?

There’s no ratio knob. The Compress/Limit switch selects a gentler or much steeper behavior (Universal Audio gives the average ratio as roughly 3:1), and the optical cell makes the response program-dependent.

Does a 1:1 ratio do anything?

On a clean digital compressor it applies no gain reduction. On analog hardware or emulations, the signal still picks up the circuit’s coloration.