dBu is a unit of analog signal voltage in decibels, referenced to 0.775 volts RMS. A signal of 0 dBu is 0.775 V; +4 dBu, the nominal level of professional line-level equipment, is about 1.228 V; +24 dBu is about 12.3 V. The “u” stands for unloaded (or unterminated): the voltage is measured without assuming any particular load impedance.

dBu is the language of analog spec sheets. Nominal operating levels, maximum output levels, converter calibration and headroom are all written in it. It sits alongside two close relatives, dBV (referenced to 1 V and used for consumer gear and microphone sensitivity) and dBm (a power unit from the telephone era), and knowing how the three relate saves a lot of confusion when connecting equipment from different worlds.

What is dBu?

Like every decibel unit, dBu is a ratio expressed on a logarithmic scale, but with a fixed reference. Voltage is a root-power quantity, so the 20 log formula applies:

level (dBu) = 20 × log₁₀(V_RMS / 0.775 V)

and to go back to volts:

V_RMS = 0.775 V × 10^(dBu / 20)

The reference is more precisely √0.6 ≈ 0.7746 V. Every 6 dB doubles the voltage, every 20 dB multiplies it by ten. dBu describes a steady voltage in RMS terms; for a sine wave the peak voltage is √2 (about 1.414) times higher, and the peak-to-peak swing twice that again.

LevelVolts RMSSine peakSine peak-to-peakEquivalent dBVWhere you meet it
-60 dBu0.775 mV1.10 mV2.19 mV-62.2 dBVLow-output mic on a moderate source
-40 dBu7.75 mV11.0 mV21.9 mV-42.2 dBVCondenser mic on a fairly loud source
-10 dBu245 mV346 mV693 mV-12.2 dBVHot instrument signal
0 dBu775 mV1.10 V2.19 V-2.2 dBVReference; EBU alignment level
+4 dBu1.228 V1.74 V3.47 V+1.8 dBVPro nominal line level, 0 VU
+18 dBu6.15 V8.70 V17.4 V+15.8 dBVCommon 0 dBFS point (EBU-style alignment)
+22 dBu9.75 V13.8 V27.6 V+19.8 dBVTypical max level of many interfaces and consoles
+24 dBu12.3 V17.4 V34.7 V+21.8 dBV0 dBFS in SMPTE-style alignment
+28 dBu19.5 V27.5 V55.0 V+25.8 dBVHigh-headroom outboard gear

All values in the table are calculated, not measured. Note how fast voltages climb at the top: a +28 dBu output needs a peak-to-peak swing of about 55 V, which is why high-headroom gear runs from higher supply rails or uses transformers.

Why 0.775 volts?

The odd-looking reference comes from the telephone network. Early telephone and broadcast lines were designed around matched impedances, usually 600 ohms, where maximum power transfer mattered. Levels were stated as power relative to 1 milliwatt: dBm. The voltage that dissipates 1 mW in 600 Ω is:

V = √(P × R) = √(0.001 W × 600 Ω) = √0.6 ≈ 0.775 V

So in a 600-ohm world, 0 dBm and 0.775 V were the same thing. The VU meter, standardized in the late 1930s by engineers from CBS, NBC and Bell Labs, read 0 VU at +4 dBm in 600 Ω, which is 1.228 V. That’s the origin of today’s +4 dBu nominal level.

Modern audio stopped matching impedances decades ago. Outputs are now low impedance and inputs high impedance, a scheme called bridging, and what passes between devices is effectively voltage, not power. Engineers kept the familiar 0.775 V reference but dropped the 600-ohm load. For a while the voltage version was written dBv with a lowercase v; because that was too easy to confuse with dBV (1 V), the industry renamed it dBu, with “u” for unloaded or unterminated.

dBu, dBV and dBm compared

UnitReferenceMeasuresCommon uses
dBu0.775 V RMSVoltage, no load assumedPro analog levels (+4 dBu), max output, converter calibration
dBV1.000 V RMSVoltageConsumer and semi-pro levels (-10 dBV), mic sensitivity (dBV/Pa)
dBm1 mW in a stated impedance (traditionally 600 Ω)PowerTelephone, broadcast, RF; older audio specs

Converting between dBu and dBV

Because 1 V is 2.21 dB above 0.775 V, the conversion is a fixed offset:

  • dBu = dBV + 2.21
  • dBV = dBu – 2.21

So +4 dBu is +1.79 dBV, and the consumer level of -10 dBV is about -7.78 dBu. The difference between the two nominal line levels is therefore about 11.8 dB, not the 14 dB you’d get by subtracting -10 from +4.

When dBm still matters

dBm only equals dBu when the load is exactly 600 Ω. Into a typical 10 kΩ line input, a +4 dBu signal is still 1.228 V, but the power it delivers is tiny, about 0.15 mW, which is -8.2 dBm. Specifying a modern line output in dBm without stating the load is a leftover from the matched-impedance era. You’ll still see dBm in RF, telecom and on vintage broadcast gear, where 600-ohm terminations were real.

Nominal level, maximum level and headroom

Two dBu numbers describe most analog equipment:

  • Nominal (operating) level: the average level the design expects, usually +4 dBu for pro gear. It’s what a VU meter reads as 0 VU on a typical studio system.
  • Maximum level: the highest level before clipping. Pro consoles, preamps and converters commonly reach +20 to +24 dBu; some outboard designs go beyond +26 dBu.

The gap between them is headroom. A device that runs at +4 dBu nominal and clips at +24 dBu has 20 dB of headroom, enough for the peaks of most music, whose short transients can rise 10 to 20 dB above the average level. Below the nominal level sits the noise floor, and the distance from nominal to noise is the signal-to-noise ratio.

dBu is defined in RMS terms, so strictly speaking it describes steady signals. When a spec says “maximum output +24 dBu,” it means a sine wave whose RMS value is +24 dBu; the actual voltage peaks are 3 dB higher. Saying a drum transient “reaches +27 dBu” mixes RMS and peak conventions; it’s clearer to say the peaks are a certain number of decibels above a stated dBu level.

dBu and dBFS: crossing into digital

There’s no universal conversion between dBu and dBFS. The relationship is set by the converter’s calibration: how many dBu at the analog input produce a full-scale digital signal. That figure appears in interface specs as “maximum input level” or “reference level.”

Alignment0 dBFS equals+4 dBu reads asWhere it’s used
SMPTE-style (US post)+24 dBu-20 dBFSFilm and TV post; many high-end converters
Avid HD I/O factory default+22 dBu-18 dBFSPro Tools HD systems
EBU-style (Europe)+18 dBu-14 dBFS (0 dBu = -18 dBFS)European broadcast
RME Fireface UFX+ (+4 dBu setting)+13 dBu-9 dBFSExample of a lower reference setting

To translate, subtract: if 0 dBFS = +18 dBu, then a signal at -10 dBFS is +8 dBu. Many converters let you trim or switch the reference, which matters when you send signals out to analog gear and back: an outboard compressor expecting +4 dBu nominal will behave very differently if your interface sends it +4 dBu at -20 dBFS versus at -9 dBFS.

dBu in practice

Connecting -10 dBV gear to +4 dBu gear

Plugging a consumer or semi-pro source (a keyboard, a DJ mixer, a media player) into a pro line input leaves the signal about 12 dB lower than the input expects. That’s usually fixable with input gain, at the cost of a little noise. Going the other way, a +4 dBu output into a -10 dBV input arrives about 12 dB too hot and may overload the input stage. Interfaces with a +4/-10 switch change the input or output sensitivity to suit, and dedicated level converters solve it in hardware.

Reading spec sheets

  • “Maximum output: +24 dBu”: the output can swing to 12.3 V RMS before clipping.
  • “Nominal level: +4 dBu”: the design reference, usually 0 VU.
  • “Input sensitivity: -10 dBV / +4 dBu switchable”: the input can be set for consumer or pro levels.
  • “Maximum input level: +18 dBu at 0 dBFS”: the converter’s calibration point.
  • “EIN: -128 dBu”: a preamp‘s equivalent input noise, a voltage far below anything else on the list. See preamp.

Analog-modeled plugins

Plugin emulations of analog gear are designed around an imagined dBu world. Their documentation often states a reference like “0 VU = -18 dBFS,” meaning a signal at -18 dBFS represents the +4 dBu nominal level of the original hardware. The reference varies by developer and plugin, so check the manual rather than assuming.

Common mistakes and myths

  • “+4 dBu and -10 dBV are 14 dB apart.” They’re about 11.8 dB apart, because the references differ.
  • “dBu and dBm are the same.” Only into exactly 600 Ω. dBu is voltage; dBm is power.
  • “The u means micro.” In audio levels, the u means unloaded or unterminated.
  • “There’s a standard dBu-to-dBFS conversion.” It depends entirely on how the converter is calibrated.
  • “+4 dBu gear sounds better.” The level standard says nothing about quality. Higher operating levels help with noise and long cables, but a well-designed -10 dBV device can be very clean.

Gear for bridging dBu and dBV

Some links in this section go to Thomann and are affiliate links: if you buy through them, musicproductionglossary.com may earn a small commission at no extra cost to you. Learn more.

When equipment can’t be switched between consumer and pro levels, a level converter does the job. Two examples:

  • Radial J+4: a stereo line driver that Radial designed to raise -10 dBV consumer outputs to +4 dBu balanced levels, with transformer isolation.
  • ART CleanBox Pro: two channels of unbalanced-to-balanced conversion and two channels of balanced-to-unbalanced, for connecting consumer gear to pro inputs and back.

Before buying one, check your interface: many already have switchable +4/-10 inputs or outputs, which makes a box unnecessary.

FAQ

What does dBu stand for?

Decibels relative to 0.775 volts RMS, with “u” meaning unloaded or unterminated: the measurement doesn’t assume a load impedance.

How many volts is +4 dBu?

About 1.228 V RMS. For a sine wave that’s about 1.74 V peak and 3.47 V peak-to-peak.

What’s the difference between dBu and dBV?

Only the reference. dBu uses 0.775 V, dBV uses 1 V. Add 2.21 dB to a dBV value to get dBu.

Why is the reference 0.775 V?

It’s the voltage that dissipates 1 milliwatt in 600 ohms, the old telephone line impedance. The audio industry kept the voltage when it stopped matching impedances.

Can dBu be negative?

Yes. Any voltage below 0.775 V RMS is negative dBu. Microphone signals are typically about -70 to -20 dBu.

How do I convert dBu to dBFS?

Look up the analog level your converter reaches at 0 dBFS. If 0 dBFS = +22 dBu, then dBFS = dBu – 22, so +4 dBu reads -18 dBFS.

Is dBu RMS or peak?

RMS. Peaks of a sine wave are 3 dB higher, and real music can have peaks well above that.