A ground loop is an unwanted current path formed when two or more pieces of equipment are connected to ground through more than one route, typically the safety ground in their power cords and the shields of the audio cables between them. Small voltage differences between those ground points drive current around the loop, and where that current flows through a signal’s reference, it adds hum at the mains frequency (50 or 60 Hz) and buzz at its harmonics. In the UK it’s often called an earth loop.

Ground loops are the most common source of hum in studios and on stages, and one of the most misunderstood. They’re harmless to people in themselves, but the classic “fix,” defeating the safety ground on a power plug, can be lethal. The right fixes work on the audio connection instead: balanced interfaces, isolation transformers, ground-lift switches and sensible power distribution.

What is a ground loop?

Most mains-powered audio gear connects its metal chassis to the safety ground (protective earth) through the power cord. When you connect two such devices with an audio cable, the cable’s shield connects their chassis a second time. You now have a loop: device A’s ground, through the building’s ground wiring, to device B’s ground, and back through the audio cable shield.

The two ground points are never at exactly the same voltage. Equipment leaks a little current into the safety ground through the capacitance between its mains wiring and the chassis, and building ground wires have resistance, so currents flowing in them create small voltage differences, often millivolts, sometimes much more. That voltage drives a current around the loop, and some of it flows through the audio cable’s shield.

Whether you hear it depends on the connection:

  • Unbalanced connections use the shield as the signal return. The noise voltage across the shield’s resistance adds directly to the audio.
  • Balanced connections keep the shield out of the audio path, and a good differential input rejects the ground difference as common-mode noise. Ground loops are still possible, mainly through equipment with a pin 1 problem (below).

It’s worth separating the ground loop from other noise sources. Hum can also come from magnetic fields (a power transformer near a cable or a guitar pickup), failing power-supply capacitors, or RF interference. A ground loop is specifically noise caused by current flowing in a shared ground path.

Why it hums: the numbers

The noise voltage developed across a cable shield is simply Ohm’s law: V_noise = I_loop × R_shield. Shield resistance is low but not zero, a few tens of milliohms for a few meters of typical cable. The table shows what loop currents through a 0.05 Ω shield do to an unbalanced -10 dBV signal (about -7.8 dBu):

Loop currentNoise voltage across 0.05 ΩNoise levelBelow a -10 dBV signal by
1 mA50 µV-83.8 dBu≈ 76 dB
10 mA0.5 mV-63.8 dBu≈ 56 dB
100 mA5 mV-43.8 dBu≈ 36 dB

Values are calculated. Noise 56 dB below the music is clearly audible in quiet passages and between songs, and 36 dB below is ugly. For reference, according to Bill Whitlock of Jensen Transformers, UL safety rules allow leakage currents up to 0.75 mA for ungrounded (two-prong) equipment and up to 5 mA for grounded equipment, and a rack full of gear adds those currents together.

A balanced input changes the picture. The same ground difference becomes common-mode noise, reduced by the input’s common-mode rejection: an input with 60 dB of real-world CMRR turns a 10 mV ground difference (-37.8 dBu) into about -98 dBu at the output, usually inaudible.

Hum vs buzz

Pure hum is a low tone at the mains frequency: 50 Hz in Europe and much of the world, 60 Hz in North America. Buzz is harsher, rich in harmonics such as 100/120 Hz and above, and usually comes from the pulsed currents drawn by rectifiers in power supplies. Ground-loop noise is often more buzz than hum because those pulsed currents end up in the ground wiring.

The pin 1 problem

In 1995, consultant Neil Muncy described in the Journal of the Audio Engineering Society why some balanced systems hummed anyway. Many products connected the XLR’s pin 1 (the cable shield) to the circuit board’s internal ground rather than directly to the metal chassis. Shield current then flowed through the circuit board’s ground traces on its way to the chassis, creating small voltages inside the audio circuitry, where no balanced input could reject them. He called it the pin 1 problem.

The fix is in the equipment design: connect shields to the chassis right at the connector. The AES standardized that practice in AES48-2005, and well-designed modern gear follows it. Older or budget gear may not, which is why a “fully balanced” system can still hum.

Shield-current-induced noise

Even with correct equipment, a large shield current can couple slightly unequal voltages into the two inner conductors of some cable designs (notably foil shields with drain wires), so a little of the noise becomes differential and passes through the input. Cables with braided or spiral shields and well-twisted pairs are less prone to it.

Ground loops with computers and USB

Laptops and desktops add their own flavor. When a laptop is charging, its power supply connects it to mains ground (or capacitively couples it), and the USB cable to the audio interface connects its ground to the interface. Add active monitors plugged in somewhere else and you have a loop that can carry not only hum but digital noise: whines and chirps that change with screen activity, disk access or mouse movement.

A quick test: run the laptop on battery. If the noise disappears, the loop goes through the laptop’s power supply. Fixes include plugging computer, interface and monitors into the same power outlet or strip, using balanced connections to the monitors, a line isolator between interface and monitors, or a USB isolator between computer and interface.

Finding a ground loop

Hunting hum by swapping random cables wastes time. A systematic approach, adapted from the method Whitlock teaches:

  1. Protect your ears and speakers. Turn the monitors down before plugging and unplugging anything.
  2. Start at the end of the chain. Disconnect the inputs of the monitors or power amplifier. If the hum stays, the problem is in that device or its power, not in a loop.
  3. Work backward one connection at a time. Reconnect each device toward the sources. When the hum appears, the connection you just made completes the loop.
  4. Test the input with a dummy plug. For a balanced input, a plug with a resistor (around 150–200 Ω) between pins 2 and 3 and nothing else simulates a quiet source. Noise with the dummy plug alone points to the device itself; noise only with the cable connected points to the interface between devices.
  5. Check the computer. Battery power, a different USB port, or disconnecting other peripherals often reveals the path.
  6. Apply a safe fix at the offending connection (next section).

Moving cables away from power transformers and power cords, and checking whether the hum changes as you move them, also helps tell magnetic pickup (which changes with position) from a ground loop (which usually doesn’t).

Fixing ground loops safely

Never defeat the safety ground

Removing or bypassing the ground pin on a power plug (a “cheater” adapter, a broken-off pin, a modified cord) often stops the hum, and it’s dangerous. The safety ground is what carries fault current and trips the breaker if a live wire touches the chassis. Without it, a fault can leave the chassis at full mains voltage, and the next person who touches it and something grounded, such as a mic stand or guitar strings, completes the circuit. It also violates electrical codes. Fix the audio side instead.

Safe fixes, roughly in order

  1. Power everything from one point. Plug interconnected gear into the same outlet or power distribution, ideally on the same circuit. This doesn’t break the loop, but it shrinks the voltage differences that drive it.
  2. Use balanced connections wherever both ends support them. See balanced audio.
  3. Use pseudo-balanced cables from unbalanced outputs into balanced inputs: the input then references the source’s own ground and rejects the difference.
  4. Insert an isolation transformer (line isolator) in the problem connection. Audio passes magnetically; no conductive ground path remains between the two devices. Good transformers are effectively transparent; very cheap ones can lose low end at high levels.
  5. Use a DI box with a ground lift for instruments, keyboards and line sources going to a mic input. Lifting pin 1 at the DI breaks the shield connection while the transformer passes the audio.
  6. Lift the shield at one end of a balanced line (a “telescoping” shield), usually at the receiving end. This only makes sense with balanced connections, and some guides suggest connecting that end through a small capacitor instead (a “hybrid” termination) to keep RF protection.
  7. Use optical or isolated digital links where possible: optical connections (TOSLINK, ADAT) have no electrical path at all.

A notch filter or noise-reduction plugin can reduce hum already recorded, but it’s a repair, not a fix, and it often removes musical low end along with the noise.

Typical ground-loop situations

SituationWhy it humsUsual fix
Keyboard or synth into an interface, monitors powered elsewhereUnbalanced output; shield carries loop currentPseudo-balanced cable, DI with ground lift, or line isolator
Laptop charging, USB interface, active monitorsLoop through the laptop’s power supply and USB groundSame power strip; balanced monitor cables; line or USB isolator
Bass amp DI out to the PA consoleAmp and console grounded at different pointsGround-lift switch on the DI or amp’s DI output
Guest console feeding a festival PADifferent power sources, possibly different generatorsTransformer isolation on the feed
Rack of outboard with unbalanced patchingMany shield paths between chassisBalanced patching, single power distribution
Tube mic with its own power supplyPower supply grounded at a different point from the preampSame power distribution; check the supply’s cable and grounding

Microphones themselves don’t create ground loops: a dynamic or phantom-powered condenser has no mains connection. Hum on a mic channel usually comes from the preamp, the cabling, magnetic fields or another device sharing the ground.

Common mistakes and myths

  • “Ground is zero volts everywhere.” Ground conductors have resistance; current through them creates voltage differences between points.
  • “Lifting the ground on a DI box is dangerous.” A DI’s ground lift disconnects the audio shield, not the safety ground. It’s the safe way to break a loop.
  • “Balanced cables make ground loops impossible.” They reject most of the noise, but pin 1 problems, unbalanced gear and poor CMRR still let hum through.
  • “A power conditioner fixes ground loops.” Most power conditioners filter and protect, but don’t isolate audio grounds. Unless it contains an isolation transformer feeding all the equipment, the loop remains.
  • “Cut the shield at both ends.” That leaves the signal wires unshielded. Lift at one end only, and only on balanced lines.
  • “Hum that stops when you touch the strings is a ground loop.” That’s usually electrostatic pickup through the body and the instrument’s shielding, a different problem.

Gear for breaking ground loops

Some links in this section go to Thomann and are affiliate links: if you buy through them, musicproductionglossary.com may earn a small commission at no extra cost to you. Learn more.

These are examples of the isolation tools described above. Features are as described by the manufacturers.

  • Behringer MicroHD HD400: a budget two-channel isolator for unbalanced and balanced lines, aimed at home studios and simple setups.
  • ART DTI: a two-channel passive transformer isolator with XLR, TRS and RCA connections, useful for mixed consumer and pro gear.
  • Palmer PLI 05: a two-channel line isolator with 1:1 transformers on 1/4-inch jacks.
  • Radial IceCube IC-1: a passive one-channel isolator that sits in an XLR line, with a ground lift.
  • Radial Twin-Iso: a two-channel balanced line isolator with Jensen transformers, a common choice for touring and broadcast feeds.
  • Radial JDI: a passive DI with a Jensen transformer and ground lift, a standard way to bring instruments and keyboards into a mic input without hum.
  • Radial ProDI: a more affordable passive DI with a custom Radial transformer and ground lift.

FAQ

What does a ground loop sound like?

A steady low hum at 50 or 60 Hz, often with a harsher buzz from harmonics at 100/120 Hz and above. With computers, it can include whines that change with what the computer is doing.

Is a ground loop dangerous?

The ground loop itself isn’t. Fixing it by removing the safety ground from a power plug is dangerous and can be lethal.

How do I fix a ground loop hum?

Power the gear from one point, use balanced connections, and if the hum remains, add an isolation transformer, a DI box with ground lift, or a pseudo-balanced cable on the connection that causes it.

Why does my laptop hum only when it’s charging?

The charger connects the laptop to mains ground, completing a loop through the USB interface and other grounded gear. On battery, the loop is broken.

Do ground loop isolators affect sound quality?

Good transformer isolators are effectively transparent. Very cheap ones can lose low frequencies or distort at high levels.

Can balanced cables stop ground loops?

They reject most ground-loop noise through common-mode rejection, but equipment with a pin 1 problem or unbalanced connections can still hum.

What is the pin 1 problem?

A design fault in which the cable shield (XLR pin 1) connects to the circuit board ground instead of directly to the chassis, letting shield current inject noise inside the equipment.