The pickup angle of a microphone is the angular region around its main pickup direction within which its sensitivity remains above a specified level relative to the on-axis response. It is often called the acceptance angle or, less precisely, the microphone’s coverage angle. The value depends on the attenuation threshold used to define the region, the frequency being considered, and the microphone’s actual polar pattern.
Pickup angle is not an invisible cone outside which sound disappears. Sound beyond the quoted angle can still enter the microphone, sometimes quite strongly. It is a compact way to describe part of a directional response, not a replacement for a full set of polar diagrams or off-axis frequency-response measurements.
Table of Contents
How a Pickup Angle Is Defined
Imagine a directional microphone pointed straight toward a person speaking. The microphone’s main axis is designated 0 degrees. As the speaker moves to one side while staying at a comparable distance, the microphone’s response generally falls. An engineer can choose a specified attenuation relative to the response at 0 degrees and find the left and right angles where that attenuation occurs.
For example, a -3 dB pickup angle describes the main frontal sector bounded by points where the microphone’s level is 3 dB below its on-axis value. If those points occur at approximately 55 degrees left and 55 degrees right, the full acceptance angle is about 110 degrees. That total angle is a description of the specified response contour, not an absolute boundary of the microphone’s ability to record sound.
The attenuation convention must be stated. A -6 dB boundary encloses a larger frontal sector than a -3 dB boundary for most smoothly directional microphone patterns. A number quoted without the threshold and frequency can therefore be misleading, especially when comparing different manufacturers or different classes of microphones.
The figures normally describe the primary front lobe. A figure-8 or hypercardioid microphone has other directions of significant sensitivity that are not part of one simple frontal acceptance cone. For these patterns, a single pickup-angle number gives only a partial picture.
Why -3 dB and -6 dB Angles Are Not Interchangeable
A 3 dB level change and a 6 dB level change represent different sensitivity ratios. In microphone response descriptions, the level is generally derived from an amplitude ratio measured at a specified signal frequency and direction.
Some guides use a -3 dB criterion when comparing idealized front pickup widths. Others show coverage angles using -6 dB or a product-specific definition. DPA’s microphone specification guidance identifies the attenuation angles for several polar patterns and demonstrates why the threshold belongs alongside the degree value.
Using the same name for different measurement thresholds can make two products look more or less directional than they really are. For a meaningful comparison, make sure the angles refer to the same attenuation threshold, the same reference axis, and a comparable test frequency or band.
Do not assume that a manufacturer has made a mistake just because its stated acceptance angle differs from a textbook ideal. Actual acoustic tuning, frequency-dependent response, and chosen conventions can all legitimately change the result.
Pickup Angle in the Ideal First-Order Pattern Family
Idealized first-order microphone models are useful for understanding the progression from broad to narrow frontal pickup. A conventional cardioid has a wider front sector than a supercardioid, which is generally wider than a hypercardioid when calculated with the same -3 dB criterion.
| Idealized response | Approximate frontal width at -3 dB | What the number does not tell you |
|---|---|---|
| Cardioid | 131° | How deep the real rear null remains at each frequency |
| Supercardioid | 115° | How the rear lobe and off-axis spectral response behave in a specific microphone |
| Hypercardioid | 105° | Whether rear or rear-side noise is better controlled in a given setup |
| Figure-8 | 90° per ideal lobe | That an equally sensitive opposite-facing rear lobe also exists |
These numbers are theoretical illustrations, not universal standards for every microphone carrying those names. The exact coefficients and reference conventions matter. For example, a published manufacturer comparison may quote different angles for nominally similar patterns. The meaningful approach is to compare real measurements with a stated threshold.
A true ideal omni has no special front pickup boundary, since its response is the same from all directions. Calling that a 360-degree pickup angle can be a convenient shorthand, but it does not represent the same front-lobe measurement used for directional patterns.
Pickup Angle Changes With Frequency
An actual microphone responds to sound waves whose wavelengths range from meters to centimeters. Capsule and housing dimensions, acoustic rear ports, and, for some microphones, interference tubes influence the directional response differently at different frequencies.
Consequently, a microphone may admit low-frequency sound over a broad angular region while becoming noticeably more selective at high frequencies. The pickup angle printed at a particular reference frequency may not describe the microphone’s behavior across an entire vocal or instrument spectrum.
This difference can be especially important for dialogue, where low-frequency room energy and high-frequency consonant information occupy different bands. A moving actor could remain within a broad midrange pickup sector while suffering a change in treble or overall tone because the upper-frequency acceptance region is narrower.
For this reason, a frequency-dependent polar plot or directivity graph is more informative than any single acceptance-angle number. When available, use the manufacturer’s measured frequency-specific curves to evaluate the microphone’s actual operating region.
How Pickup Angle Affects Aiming a Microphone
A microphone’s angle of pickup matters when a source moves. A performer who turns their head, a speaker walking across a stage, or a boom microphone following an actor can all change the angle at which the sound reaches the capsule.
A broad pickup region can be forgiving of some movement but may admit more surrounding sound. A narrower region can improve directivity but require closer attention to aiming. The challenge is to capture the wanted source consistently while managing undesirable sound from other directions.
In practical placement, distance and angle interact. Moving a microphone closer to an actor often improves the direct-to-ambient ratio more than a small change in pickup-angle specifications. But if the capsule is near the edge of the frame or must follow multiple actors, a very tight frequency-dependent pattern can introduce unstable tone as people move. The related off-axis response determines how strongly that tonal balance changes with angle.
A close source also changes low-frequency response for many directional pressure-gradient microphones through the proximity effect. That mechanism is separate from pickup angle, although both influence the recorded sound and both matter when setting working distance.
Stage Monitors, Rejection Nulls, and Feedback
The acceptance angle describes the microphone’s primary frontal pickup sector. It does not identify the exact directions of maximum rejection. For a cardioid, the ideal null is directly behind the microphone. For supercardioid and hypercardioid patterns, rejection nulls lie toward the rear sides, and a smaller rear pickup lobe remains.
On stage, placing a monitor based only on a quoted frontal acceptance angle can be a serious mistake. Instead, examine the full polar response and identify where monitor sound approaches the capsule. The deepest rejection direction, when practical, can be a better placement cue than the apparent width of the front lobe.
Real feedback behavior also depends on the system’s gain, speaker dispersion, room reflections, microphone position, and the frequency at which the system becomes unstable. A null measured at one frequency does not guarantee the same attenuation at all frequencies. A performer rotating or cupping a microphone can further alter the designed response.
Pickup Angle Is Not the Stereo Recording Angle
A particularly important confusion occurs in stereo microphone design. The pickup or acceptance angle refers to the directivity of an individual microphone. The stereo recording angle (SRA) describes the region of the real soundstage that a particular stereo microphone arrangement maps between its left and right playback positions.
SRA depends on a combination of directional patterns, angle between microphones, spacing, and the stereo system’s level and time differences. In near-coincident setups, microphone separation contributes timing cues that cannot be described by one microphone’s pickup angle alone.
For example, two wide cardioids may each have a broad individual pickup region, yet the stereo image formed by the pair depends on how the microphones are angled and spaced. A wide microphone pickup angle does not imply that the stereo array will map the same soundstage width accurately.
Similarly, the figure-8 Side microphone in Mid-Side recording has a known directional geometry, but the decoded stereo width also depends on the level of the Side component. The individual pickup angle and the completed array’s stereo recording angle are distinct concepts.
Shotgun Microphone Acceptance Angles
A shotgun microphone combines a directional capsule with an interference tube. The tube adds frequency-dependent cancellation of off-axis sound, especially where the sound wavelength is short enough for the structure to be effective.
As a result, a shotgun may have a relatively tight high-frequency main lobe while retaining broader pickup at lower frequencies. Its acceptance angle is not one fixed cone across the audio band. Sound just outside the high-frequency main region may also acquire irregular tonal coloration rather than simply fading away.
This matters when booming dialogue or recording wildlife. Precise aiming helps keep the wanted source in the more consistent pickup region, but microphone distance, room reflections, wind, and off-axis sound still influence the result. Shotguns do not magnify distant sound; their benefit comes from changing the ratio of sound arriving from different directions.
Reading an Acceptance-Angle Specification Correctly
- Find the attenuation criterion. Does the figure describe -3 dB, -6 dB, or another boundary?
- Check the test frequency. A microphone may have different acceptance widths at 1 kHz and 8 kHz.
- Verify that the number refers to full width. Some diagrams report one side of the axis, while others report the full included angle.
- Identify secondary lobes and nulls. A hypercardioid can pick up significant rear sound even with a narrow main pickup angle.
- Examine off-axis tonal behavior. Angle determines more than level if frequency response changes with direction.
- Consider the recording task. Source movement, room quality, monitor geometry, and stereo design can make different aspects of the complete polar pattern more useful.
The acceptance angle is most helpful as one measurement within a larger set, not as the primary score for ranking microphones.
Common Mistakes
“Anything outside the angle will not be recorded.” Pickup is not a digital cutoff; attenuation normally changes continuously with angle and frequency.
“A 105-degree microphone is always better at isolating sound than a 115-degree microphone.” Its other lobes may capture more of the actual competing sound, and its off-axis coloration may matter more in the final mix.
“The pickup angle of one microphone is the stereo recording angle of a pair.” SRA describes spatial image mapping by an arrangement, not just the directivity of a single capsule.
“Every manufacturer uses the same dB threshold.” Always identify the criterion and check real measured plots.