A shock mount is a microphone holder that suspends the mic in elastic bands or flexible plastic so vibrations traveling through the stand don’t reach the capsule. Footsteps, a tapping foot, a bumped desk, traffic rumble and even the air conditioning can travel up a mic stand as mechanical vibration, and a sensitive microphone turns that into low-frequency thumps and rumble.
Shock mounts are standard with studio condenser microphones, especially large-diaphragm models, and on boom poles for film and TV. Many mics come with a dedicated one; others need one bought separately.
Table of Contents
What is a shock mount?
A shock mount has two parts: a rigid outer frame that attaches to the stand, and an inner holder that grips the microphone. The two are connected only by flexible elements, traditionally crossed elastic cords (the “cat’s cradle” design), or modern molded plastic suspensions. Vibration arriving at the frame has to pass through those flexible links to reach the mic, and most of it doesn’t make it.
The terms shock mount, shockmount, suspension mount and elastic suspension all describe the same thing. A plain rigid mic clip is the opposite: it couples the mic directly to the stand.
A shock mount deals with structure-borne noise, meaning vibration traveling through solid materials. It does nothing for airborne noise, like a fan or traffic heard through the window. That needs mic placement, a directional pattern and room treatment.
How a shock mount works
A mass on a spring
A microphone in a shock mount is a mass on a spring. Every such system has a natural resonant frequency:
f₀ = (1 ÷ 2π) × √(k ÷ m)
where k is the stiffness of the suspension and m is the mass of the microphone. Below f₀, the mic moves with the stand as if rigidly attached. Near f₀, the suspension actually amplifies vibration. Above about 1.4 × f₀, it starts to isolate, and the isolation improves rapidly as frequency rises.
Isolation in numbers
For an ideal undamped mass-spring system, the fraction of vibration that gets through (the transmissibility) is 1 ÷ |1 − (f ÷ f₀)²|:
| Frequency relative to resonance | Vibration transmitted | Isolation |
|---|---|---|
| 1 × f₀ | Amplified | None (resonance) |
| 1.4 × f₀ | About the same | About 0 dB |
| 2 × f₀ | About one third | About 9.5 dB |
| 3 × f₀ | About one eighth | About 18 dB |
| 5 × f₀ | About one twenty-fourth | About 28 dB |
| 10 × f₀ | About one hundredth | About 40 dB |
Real suspensions include some damping, which reduces the peak at resonance at the cost of slightly less isolation higher up. The principle stays the same: the resonance must be well below the frequencies you care about. Sound On Sound‘s Hugh Robjohns recommends a resonant frequency somewhere below 6 to 8 Hz, noting that a shock mount isolates effectively above roughly three times its resonance and amplifies vibration at resonance.
Why the mic’s weight matters
Because f₀ depends on both stiffness and mass, a shock mount is tuned for a certain weight range. A heavy mic in a light-duty mount sags, lets the inner holder touch the frame or bottoms out, and short-circuits the isolation. A very light mic in a stiff mount raises the resonant frequency into the audible bass, which makes the mount less effective. That’s why manufacturers make dedicated mounts for specific mics and why universal mounts list a supported weight and diameter range.
Types of shock mounts
Elastic cord (cat’s cradle)
The classic design uses elastic cords strung in a crisscross pattern between two rings. It’s simple and effective, and it’s what many studio mics ship with. The cords lose tension and stretch over time, especially under a heavy mic, so they need replacing every few years.
Molded plastic suspensions
Rycote’s Lyre suspension, introduced in 2007 according to Sound On Sound, replaced elastic cords with molded, harp-shaped supports made from Hytrel, a thermoplastic elastomer. Lyres don’t sag or snap like elastic and keep the mic centered. The design is now used in Rycote’s InVision studio and boom mounts and by other manufacturers in their own variants.
Dedicated and universal mounts
A dedicated mount fits one mic model, often by screwing onto the mic’s base thread, as with Neumann’s EA series for its large-diaphragm mics. Universal mounts grip mics within a range of diameters. Dedicated mounts usually fit better and hold the mic more securely; universal mounts are flexible and cheaper.
Internal shock mounting
Many mics isolate their capsule inside the body with rubber or foam. Handheld vocal mics rely on this to reduce handling noise, and broadcast dynamics such as the SM7B and RE20 have internal shock mounting, so an external mount is less critical (EV still makes a dedicated suspension for the RE20). Small-diaphragm condensers often have some internal isolation but still benefit from an external mount on a boom.
Boom pole and pistol-grip mounts
Film and TV boom operators use suspensions designed for shotgun mics, often combined with a windshield and a pistol grip. These must isolate handling noise from a moving pole, which is a harder job than isolating a stationary stand.
Setting up a shock mount
- Choose a mount rated for the mic’s weight and diameter, or use the mic’s dedicated mount.
- Attach the mount to the stand and tighten it so it can’t rotate. Check the thread: many European stands use 3/8-inch threads, US stands 5/8-inch; an adapter is often needed.
- Insert the mic so it’s centered and doesn’t touch the outer frame. With side-address mics, make sure the front of the mic faces the source.
- Tighten any locking ring firmly but without forcing it.
- Leave a loose loop of cable between the mic and the stand. A taut cable is a rigid bridge that carries vibration straight past the suspension.
- Tap the stand gently while monitoring and listen. A well-isolated mic should produce only a faint thud.
Use the mount’s angle adjustment carefully with heavy mics: tilted far forward, a large condenser can rotate in the mount or lean on the elastics. Tighten the angle lock before letting go.
Shock mounts in practice
Studio vocals
Singers tap feet, move their hands, touch the stand and sometimes the mic. A shock mount, a pop filter and a sturdy stand are the standard vocal setup. Even with a mount, some low-frequency rumble can get in through the air or the floor, so a high-pass filter on the vocal channel is common practice.
Podcasting and desktop setups
Desk-mounted mics pick up typing, mouse clicks and bumps through the boom arm. A shock mount reduces those noises considerably, though a heavy keyboard thump can still get through. Keeping the boom arm off the desk you type on, or clamping it to a separate surface, helps more than anything.
Live sound
On stage, vibration from the floor, drum risers and nearby subwoofers travels up stands. Shock mounts are common on overhead and choir mics and for condensers on instruments. Rigid clips are still common on rugged dynamic mics, which have good internal isolation.
Drums
Drum mics are often clipped directly to the drums or the hardware, where the vibration source is the drum itself. Here the mic’s internal isolation and placement matter more than an external suspension.
Troubleshooting
| Symptom | Likely cause | What to try |
|---|---|---|
| Thumps when the stand is touched | No mount, a worn mount, or a taut cable | Fit a mount; replace elastics; loosen the cable |
| Mic sags or touches the frame | Mount overloaded or elastics stretched | Use a mount rated for the mic; replace the elastics |
| Low rumble in all recordings | Building or traffic vibration, airborne noise | Use a high-pass filter; check the stand’s position; treat the room |
| Mic rotates or droops | Loose angle joint or thread | Tighten the joint; check the thread adapter |
| Rattle or buzz | Loose parts, a vibrating clamp | Tighten all screws; check the mount’s components |
Common mistakes and myths
- “A shock mount removes all low-frequency noise.” It only blocks vibration traveling through the stand. Airborne rumble needs other solutions.
- “Any shock mount fits any mic.” The mount must match the mic’s size and weight to work properly.
- “The cable doesn’t matter.” A tight cable bypasses the suspension.
- “Old elastics are fine as long as they hold.” Stretched elastics change the suspension’s tuning and can let the mic touch the frame.
Shock mounts to know
Some links in this section go to Thomann and are affiliate links: if you buy through them, musicproductionglossary.com may earn a small commission at no extra cost to you. Learn more.
- Rycote InVision USM: a universal studio mount with Lyre suspensions, for a wide range of mic diameters.
- Røde SM6: a shock mount with an integrated, removable pop filter for Røde large-diaphragm mics.
- Neumann EA 87: the dedicated elastic suspension for the U 87 family.
- Neumann EA 1: the elastic suspension supplied with the TLM 103 studio and mono sets, also used with other Neumann large-diaphragm mics.
- AKG H85: a universal elastic shock mount for medium-sized studio mics.
- Electro-Voice 309A: the dedicated suspension for the RE20 and related EV mics.
- Rycote InVision INV-7: a Lyre-based suspension for shotgun mics, used on boom poles and stands.
FAQ
Do I need a shock mount for my microphone?
For a studio condenser on a stand, especially a large-diaphragm model, yes. Dynamic mics with good internal isolation often work fine in a rigid clip.
Does a shock mount reduce background noise?
Only noise traveling through the stand or floor. Noise traveling through the air reaches the mic regardless.
Why is my mic still picking up thumps with a shock mount?
Check that the cable hangs loosely, the elastics aren’t worn, the mic doesn’t touch the frame and the mount is rated for the mic’s weight.
Can I use a universal shock mount?
Yes, if the mic’s diameter and weight are within the mount’s range. A dedicated mount usually fits more securely.
How often should I replace shock mount elastics?
When they lose tension or the mic sags. Under a heavy mic, that can happen within a few years. Lyre-type suspensions don’t need replacing in the same way.
What is the difference between a shock mount and a mic clip?
A mic clip holds the mic rigidly; a shock mount suspends it in a flexible holder that isolates it from vibration.